BMW Oil Capacity by Engine: B38, B47, B48, B57, B58 & More

BMW standing in Leeds, UK, near MT Auto Parts

Photo by Tjaard Krusch on Unsplash


Knowing your BMW's oil capacity saves guesswork at service time and stops you from buying too little oil or overfilling the engine. The figure depends on the engine rather than the model name, so a 320d and a 520d with the same engine take roughly the same amount. The chart below covers the main engines fitted to F- and G-generation BMWs from 2012 onwards.

BMW Engine Oil Capacity Chart

Figures are approximate service-fill quantities, including a new oil filter, as published in oil manufacturer and parts catalogue data. Where sources give a range, the range is shown.

Engine

Type

Example models

Approx. capacity

B37

1.5 diesel, 3-cyl

116d (F20 from 2015)

4.4 L

B38

1.5 petrol, 3-cyl

116i, 118i (F20 from 2015)

4.25 L

B47

2.0 diesel, 4-cyl

118d, 320d, 520d, X3 20d

5.0–5.5 L

B48

2.0 petrol, 4-cyl

120i, 320i, 330i, 520i, 530i

5.25 L

B57

3.0 diesel, 6-cyl

330d, 530d, 540d, X5 30d

6.5 L

B58

3.0 petrol, 6-cyl

M140i, M240i, 340i, 440i, 540i

6.5 L

N13

1.6 petrol, 4-cyl

116i, 118i (F20 to 2015)

4.25 L

N20

2.0 petrol, 4-cyl

320i, 328i, 520i (F-series)

5.0 L

N47

2.0 diesel, 4-cyl

118d, 320d, 520d (to 2015)

5.0–5.2 L

N55

3.0 petrol, 6-cyl

M135i, 335i, 435i, 535i

6.5 L

N57

3.0 diesel, 6-cyl

330d, 530d, 535d, X5 30d

6.5–7.0 L

 

*Check your own car: Capacities can vary with the model, sump design, xDrive and production date, and a few sources list slightly different figures for the same engine. Your owner's handbook or a BMW dealer can confirm the exact figure for your VIN.

How to Read the Chart

BMW's newer engines are built on a modular design, with roughly 500 cc per cylinder. That makes the pattern easy to remember: three-cylinder engines (B37, B38) take a little over 4 litres, four-cylinder engines (B47, B48) around 5 to 5.5 litres, and six-cylinder engines (B57, B58) around 6.5 litres.

The older N-series engines follow a similar pattern. The N47 four-cylinder diesel takes about the same as its B47 replacement, and the N55 and B58 six-cylinder petrols share the same 6.5-litre service fill. High-performance M engines and V8s, such as the N63, are not shown, because they hold considerably more and vary widely by model.

Checking the Oil Level on a Modern BMW

Most F- and G-generation BMWs have no dipstick. The engine measures its oil level electronically, and you check it through the iDrive menu or the instrument cluster. For an accurate reading, the engine needs to be at normal operating temperature and the car parked on level ground. The measurement can take a few minutes, and on some models the engine needs to be running.

After an oil change, the system may not show a reading straight away. It is better to add oil gradually and recheck than to pour in the full quoted capacity in one go, because some old oil always stays in the engine. Overfilling is as harmful as running low, and can lead to oil leaks and seal damage.

Which Oil Does Your BMW Need?

Capacity is only half the answer. BMW approves oils to its own Longlife standards, and the approval matters more than the viscosity printed on the bottle. Most BMW diesels with a particulate filter need a Longlife-04 approved oil, and some newer petrol engines specify low-viscosity grades approved to Longlife-17 FE+. The approval required for your engine is listed in the owner's handbook, and reputable oil brands show BMW approvals on the label.

Topping up between services with the wrong oil is a common mistake. If you are unsure, buy a small bottle of the correct approved oil and keep it in the boot.

Oil Capacity After an Engine Replacement

A replacement engine needs a full fresh fill, plus a new filter, before it is started. If you are fitting a used engine from MT Auto Parts, where every listing shows the donor car's recorded mileage and the engine code, use the capacity for that engine code rather than the badge on the car. It is also worth changing the oil again after the first few hundred miles to clear any residue from storage or fitting. 

Some Frequently Asked Questions

How much oil does a BMW 320d take?

An F30 or G20 320d with the B47 engine takes around 5.0 to 5.5 litres, including the filter. An earlier F30 320d with the N47 takes around 5.0 to 5.2 litres.

How much oil does a B58 engine take?

Around 6.5 litres, including the filter, in models such as the M140i, M240i, 340i, 440i and 540i.

Does the oil capacity include the filter?

The figures in this chart are service-fill quantities, which include a new filter. If you drain the oil without changing the filter, slightly less will be needed.

Disclaimer: This chart is for general guidance only. Oil capacities are approximate and are compiled from published oil manufacturer and parts catalogue data. They can vary by model, market and production date. Always confirm the exact capacity and oil specification for your vehicle in the owner's handbook or with a BMW dealer before servicing. 

Popular posts from this blog

BMW M57 Engine: Every Model That Has It (And Why It's So Reliable)

BMW Diesel Engines Ranked: The Most Dependable Options for UK Drivers

What Are Common BMW B57 Engine Problems?